How to Reset Canon MP258

If your printer show P07 error it means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:  Entering Service Mode
You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.
2. Hold down STOP/RESET button and press Power button.
3. Keep holding down Power button and let STOP/RESET button go.
4. Then Press STOP/RESET button twice then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"
2. Load some papers in your printer and press the "Main" Button once, wait until the printing is done.
3. Then press "EEPROM Clear" button to clear EEPROM.
4. Then press EEPROM button and the printer will print some text.
5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!
Warning: Getting rid of the error message won’t change that you might end up with ink leaking out of the printer if you don’t either replace or clean them.
this is a new service tool
Please leave a comment or say thank!
You might also like:

95 comments:

Anonymous said...

i use these setting and it works...hope others can learnt on this option.tq.matt

Anonymous said...

thanks alot!!!

Anonymous said...

it works! thanksss!

Anonymous said...

thanks a lot

Anonymous said...

How about ink level reset?Can this tools reset the ink level so that blinking led(Color and Black)would turn OFF?

Noob on January 8, 2011 at 9:43 PM said...

sorry u cant reset the ink level.

Anonymous said...

It works for me!!! Galing! THANKS!

Anonymous said...

HUSAY! Thanks...

Anonymous said...

its really great thank you very much

Anonymous said...

My Canon will not go into service mode. When I follow the steps, it turns on and doesn't show the error msg but the Alarm light starts blinking and 0 never appears. Any ideas?

Anonymous said...

OMG! Ang galing mo! Salamat po

Anonymous said...

maraming-maraming salamt po,tunay na kapaki-pakinabang...

Anonymous said...

i can't find the reload button.. pliz help me out, guys!!!

Anonymous said...

thanks it really works! 101% the best! :-) i du not need to call a technician, i can do it now, all by my self! :-)

Anonymous said...

Thanks!Works 100%

Anonymous said...

where can i download resetter??? help

Anonymous said...

HELP!!! EVERYTIME I PRESS THE MAIN BUTTON THE SERVICE TOO HANGS UP, WHAT SHOULD BE THE OTHER PROBLEM?

Anonymous said...

SALAMT PO NG MARAMI AFTER 2 MONTHS NA MAY ERROR NGAUNAY WALA NA SALAMAT SA TAONG ITO NA SOLVE NA ANG PROBLEMA KO S PRINTER KO..

Anonymous said...

na-solve rin ang problema ko!!!

tol magparami ka ng lahi!!!

Anonymous said...

when to power on?????

BHENTECH TV on June 29, 2011 at 9:54 AM said...

How to use the program can't see reload button. There is an error 006 when i click main button. Software doesn't workS

Anonymous said...

please help. The orange alarm continues to blink even after going through the 1st steps indicated above. What should I do next?

Anonymous said...

try downloading a new servicetool version

Anonymous said...

Im so close of throwing this printer to junk shop...I'm glad I have found your blog...Thanks...

Anonymous said...

got Error code : 006 please help. i have follow the instruction above and i got this error massage

Anonymous said...

i try the following instruction above an i got an error massage error code 006 please help

lance on July 18, 2011 at 1:29 AM said...

Thanks for the infos sir I tried the instruction but on the last part when i clicked the EEPROM button it says 006 error why is that sir?

Anonymous said...

thank you

Lb said...

SUPER THHANKSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS........

Anonymous said...

Thank you very much for your sharing.


Your such a blessing to me......Thanks a lot talaga!

Anonymous said...

nid ko ng manual rest ng ip 4760. . sakit n ulo ko kkhanap. . pls haelp po. .

Anonymous said...

Afternoon sir, pls help me how to fix my canon mp258 5012 service error. power and alarm still blinking can't go to zero.....i need a solution now...Thanks people here.

Noob on August 22, 2011 at 2:20 PM said...

Error 5012 is flatbed motor scanner error check this link for more info.

http://pcmediks.blogspot.com/2010/11/canon-pixma-error-codes-and-solution.html

Anonymous said...

you are an angel. thank you so much!!!

Anonymous said...

thanks it works 100%....

jenny on August 31, 2011 at 7:01 AM said...

thank you very much!!!!:)

jenny on August 31, 2011 at 7:02 AM said...

thank you thank you!!!!:)

Anonymous said...

pls help. 15e in my lcd in mp258 . pls help pls pls.

Noob on September 1, 2011 at 6:13 PM said...

for E15 error check your Ink cartridge

Anonymous said...

thanks thanks so much

Anonymous said...

thanks

Anonymous said...

it works!!thanks

Anonymous said...

cant download..

Anonymous said...

thank you so much... May God bless you.

Anonymous said...

thank you very much!!! 1000% works with my printer. GAHI KA AAAHHHH!

Bisnis pulsa on September 23, 2011 at 11:46 AM said...

Very very well Thank you for your sharing Great help for me

Anonymous said...

thank you

Anonymous said...

thank you so much! this one is really works! I've been tried other sites but this one is real! I hope, other's found this one for them to help for their Canon Printer..

Anonymous said...

thank you boss!

Anonymous said...

Thanks alot!!!!!!!!!!
Really Help me alot......

Anonymous said...

Im so close of throwing this printer to junk shop...I'm glad I have found your blog...Thanks...

Anonymous said...

thank you so much, thank you,,, thank you... it is a very helpful blog,,,,

Anonymous said...

good job! this tool really works! i'll recommend this to my friends. =)

Anonymous said...

why i can't open the donwloaded file when i click it twice?..it uses VLC to open..what i should use to open it?..

Anonymous said...

It was great!! it slove my problem, inclueding error code P10.. Thx!

RUSLI on November 13, 2011 at 5:58 AM said...

thanks

04CasimirM on November 16, 2011 at 10:25 PM said...

thank you!

bhenfb said...

i'm in the service mode state but when im trying to used the service tool.exe then press the main button the printer will not responding..
what should i do in this kind of situation..?
hoping your reply...... tnx

Anonymous said...

After turning on when I press print it shows "E" next to Power button. What does it mean? I cannot print.

Anonymous said...

tnx po.......

Anonymous said...

di po gumagana sa ink absurber full.

Anonymous said...

Thank you very much! My hands off to you man! You are the best!

Anonymous said...

great!tq :)

cijhei on December 22, 2011 at 9:27 AM said...

i have a query what happened to the service tool if it has an error code 006 ?

Anonymous said...

mga sir... meron bang magagamit na tool para maireset din un ink level para mawala un blinking LED ng BLACK/COLOR... help nman... tnx

Anonymous said...

thank you !!! it works, save my money ;-)

Anonymous said...

thank you.... so much

Anonymous said...

i have a new canon IP 4790. do you have a resetter for this printer sir?

Anonymous said...

SAN MAKAKA DOWNLOAD NG RESETTER?

Anonymous said...

it works.....

thanks!

Anonymous said...

MY ALARM LIGHT IS BLINKING

vaae on January 18, 2012 at 9:49 AM said...

hi...i've encountered error NO. 6000. i tried to follow the steps indicated above but it doesn't worked out.can u help me solve this problem?thanks

Anonymous said...

THANKS A LOT

Anonymous said...

Thanks..but how to replace the ink absorber??
can it be obtained easily at printer shops and replacable by non-technical people?

Anonymous said...

the program is not responding

Anonymous said...

It works perfect. Thanks! You will be blessed with abundance!
peterink

Anonymous said...

thanks ...success

Anonymous said...

thanks, it really works.

Anonymous said...

matur suwun...

Anonymous said...

thank you so much !!!
well done !!

Best regards from Malaysia

Anonymous said...

Thank you so much...THUMBS UP!!!! so easy.. the instruction and the resetter software is all there.

Anonymous said...

Error Code 002 on EEPROM

Anonymous said...

thanks..... works perfectly......

jmjulie25 on April 10, 2012 at 12:18 PM said...

Thank you very much.. it works perfectly

Anonymous said...

Thanks much! It works again!

Anonymous said...

Salamat ng marami!

Anonymous said...

thans bro....!!!

Anonymous said...

Thank you so much.. :)

Anonymous said...

Thank you very much! The ink levels still blink but I can still print. It's like forcing your printer to print!!! :)

Anonymous said...

tq

Anonymous said...

Thanks a lot!!

Unknown on June 21, 2012 at 5:40 PM said...

great.. it works...thank u so much :)

Anonymous said...

thanks very much matur nuwun juragan...

Anonymous said...

anybody know hot to fix this problem: http://www.youtube.com/watch?v=71JABSADRCc
plesssssssssssssssssssssssss!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Anonymous said...

thank u very very much po sa site n to ...

Post a Comment

 

PC Mediks Copyright © 2009 BeMagazine Blogger Template is Designed by Blogger Template